HVAC & Plumbing Services in Angola, IN

Performed AC start-up procedures on recently installed system using Fieldpiece SMAN digital manifold gauge to verify proper refrigerant pressures, superheat, and subcooling readings. All system parameters measured within acceptable ranges, confirming successful installation and operational readiness.

Responded to no hot water complaint following recent AC installation in tight workspace. Upon arrival, inspected gas water heater and verified gas control valve had been inadvertently switched to off position, likely bumped during AC installation work. Restored gas supply to water heater, relit pilot light, and verified proper operation and hot water delivery to fixtures throughout home.

Installed PHCC battery backup combination sump pump system in basement sump basin. The installation included mounting the primary blue pump unit in the circular concrete basin, connecting multiple discharge pipes including white PVC piping, and routing electrical cables for power supply. Configured the battery backup system to provide emergency pumping capability during power outages, ensuring continuous flood protection for the property.

# HVAC Complete System Installation Successfully completed full HVAC system replacement including installation of Carrier Comfort Series single-stage air conditioner (model 26SCA424N003), evaporator coil (model CVAVA3014XMA), and single-stage gas furnace (model 58SB0B070M14--12). Removed and recycled existing equipment from residential property. ## Equipment Installation Installed outdoor condensing unit on new 2" PVC pad against exterior wall with proper clearances maintained. Mounted new electrical disconnect and whip for condenser power supply. Positioned evaporator coil and furnace indoors, completing changeout from existing 80% efficiency system. All equipment installed per manufacturer specifications and local code requirements. ## System Connections and Testing Reconnected to existing refrigerant line set after performing thorough flush and pressure test to verify system integrity. Reconnected existing supply and return ductwork to new furnace plenum. Performed refrigerant

Responded to callback for pilot light outage on Teledyne Laars boiler, second occurrence within days raising concern for potential gas leak. Upon arrival, inspected boiler system, gas supply lines, and pilot assembly. Conducted combustion analysis and gas leak detection testing throughout system. Photographed equipment nameplate and mechanical room setup for documentation. Verified proper gas pressure, checked thermocouple operation, and tested safety controls. Relit pilot light after ensuring safe operating conditions and confirmed stable flame operation before departure.

Performed seasonal maintenance on tankless water heater system, completing thorough flushing and cleaning procedure to remove mineral buildup and ensure optimal performance. Inspected all plumbing connections, verified proper operation of unit, and confirmed system functionality. Service completed within scheduled timeframe to accommodate customer's additional HVAC appointment later in the day.

Responded to service call for split copper pipe supplying exterior hose bib. Upon inspection, accessed crawl space and located compromised copper water line running through insulation between floor joists. Pipe exhibited visible split consistent with freeze damage from winter conditions. Repaired damaged section of copper supply line and verified system integrity. Tested water flow to exterior spigot and confirmed no active leaks present.

Performed comprehensive air conditioning tune-up on Carrier outdoor condensing unit. Completed standard maintenance protocol including system inspection, cleaning of condenser coils, verification of refrigerant levels, and testing of electrical components to ensure optimal cooling performance for the upcoming season.

Responded to no cooling call and performed system evaluation. Upon inspection, determined existing Coleman furnace and air handler system required replacement due to failed cooling components. Provided comprehensive estimate for complete HVAC system replacement including new air handler unit, necessary refrigerant lines, electrical connections, and ductwork modifications. Documented existing equipment configuration with furnace installation in utility closet, copper refrigerant lines, and current duct connections to support replacement specifications.

Provided estimate for replacement of 2006 Carrier gas furnace following basement flooding caused by sump pump failure. Water intrusion resulted in blower circulating water throughout the system, and inducer motor exhibited excessive noise independent of water damage. Unit currently operational but replacement recommended due to age and water exposure compromising long-term reliability.

Completed full HVAC system installation including Carrier 26SPA636W003 Performance Series single-stage air conditioner and Carrier CVAVA4217XMA evaporator coil. Removed and recycled existing equipment, installed new 2" PVC condenser pad, reconnected to existing line set with complete flush and pressure test to verify system integrity. Installed new disconnect and whip for proper electrical connection, mounted air handler unit in utility closet with PVC condensate drainage lines and proper clearances. Performed comprehensive system startup, verified refrigerant charge, airflow, and all operational parameters within manufacturer specifications. Completed post-installation quality assurance inspection, explained system operation to homeowner, and registered equipment warranty with manufacturer.

Conducted on-site evaluation for air conditioning replacement in detached garage space. Assessed existing conditions including structural layout, electrical access points, and optimal equipment placement for new AC unit installation. Documented current space configuration and provided comprehensive estimate for standalone cooling system to serve the garage area.

Completed scheduled plumbing maintenance on Freedom brand tanked water heater. Performed comprehensive water heater flush to remove sediment buildup and maintain optimal unit performance. Inspected all connections, valves, and pressure relief components for proper operation. Unit operating within normal parameters upon completion of maintenance service.

Installed Honeywell Home Elite Pro thermostat with EIM (Equipment Interface Module) model EIM007U. Completed all wiring terminations at thermostat base and interface module, verified proper connections at terminal blocks, and confirmed system power and communication status through LED indicators on the EIM board.

Responded to emergency call for failed sump pump with 6-8 inches of standing water in basement. Upon arrival, extracted standing water and assessed existing sump pump system. Determined primary pump had failed and required replacement. Installed new sump pump unit in existing pit with proper discharge piping configuration using PVC components. Connected system to existing pressure tank and copper discharge line with appropriate fittings and shutoff valve. Verified proper float operation and pump cycling. Tested complete system under load to ensure adequate water removal capacity and confirmed proper discharge through exterior line. System restored to full operational status with no standing water remaining in basement.

Responded to water leak at basement bathroom urinal with inoperable shut-off valve. Upon inspection, found heavily corroded brass supply valve assembly with significant verdigris buildup and mineral deposits affecting operation. Replaced defective shut-off valve, restored proper water control to wall-mounted urinal fixture, tested flush mechanism for proper operation, and verified all connections were leak-free.

Performed complete flush service on 75-gallon gas-fired State ProLine water heater located in basement. Drained sediment buildup from tank bottom, flushed unit until water ran clear, and inspected all plumbing connections, copper supply lines, and pressure relief valve for proper operation. System returned to full operational status with improved efficiency.

Conducted comprehensive assessment of existing HVAC system at duplex residence for complete gas furnace and air conditioning replacement. Homeowner reported inadequate cooling performance during previous season with elevated utility costs, attributed to potentially undersized equipment for space with high ceilings. Evaluated garage-mounted furnace installation and exterior condensing unit. Documented current system configuration including ductwork, electrical connections, and equipment placement. Photographed existing outdoor AC unit on concrete pad with associated electrical conduit and indoor furnace unit with visible air filtration system. Provided detailed replacement estimate addressing proper equipment sizing requirements to accommodate elevated ceiling heights and improve cooling efficiency. Discussed financing options as requested.

Performed initial assessment of furnace system in attic space. Identified access constraints preventing completion of thermostat wiring installation. Inspected HVAC unit and documented equipment details, including belt component showing wear on Megadyne MXV2-940 belt. Determined that thermostat wiring location needs to be traced before proper installation can proceed. Scheduled return visit with technician capable of accessing confined attic space to complete thermostat wiring and installation work.

Responded to no cooling complaint at commercial facility with multiple HVAC units located on steep roof and several malfunctioning thermostats. Accessed attic crawl space to inspect thermostat wiring and HVAC ductwork routing through registration area. Initial diagnostic visit completed; due to roof access safety concerns requiring two-person crew and complexity of multiple thermostat issues, follow-up service appointment scheduled to complete repairs and restore cooling functionality to affected zones.