HVAC & Plumbing Services in Angola, IN

Performed startup and commissioning on two newly installed air conditioning systems. Verified refrigerant charge at 7.66 lbs on Carrier 36SCA448N003 unit, confirmed proper system pressures and temperatures using digital manifold gauges, and documented all operational parameters within manufacturer specifications.

Responded to report of suspected water leak with sump pump and well pump cycling at irregular intervals. Conducted initial inspection of crawl space access point measuring approximately 2x3 feet at foundation level. Documented exterior foundation conditions, crawl space entry point, and surrounding soil moisture levels through photographic documentation for further assessment of potential underground leak in crawl space area.

Responded to repair damaged plumbing exhaust vent lines in attic space that were broken during recent roof installation. Accessed attic area and inspected white PVC vent piping with purple primer markings running vertically through roof structure. Assessed damage to vent stack and connections where roofing contractor had compromised the existing plumbing ventilation system. Repaired and reinstalled proper venting configuration to restore functionality of plumbing exhaust lines, ensuring all connections were secure and properly sealed. Verified vent pipes extended correctly through roof penetrations and all joints were watertight to prevent future leaks or system failures.

Performed inspection and evaluation of existing sump pump system per customer request to assess current discharge configuration and explore alternative routing options. System was found to be operational but functioning below optimal efficiency. Examined white PVC discharge piping with dual ball valves, vertical run through floor joists, and connection points in basement area. Assessed pump unit positioning on concrete floor, electrical connections, and current discharge path routing along foundation walls. Identified opportunities for system modification to improve discharge flow and overall performance. Documented existing installation with photographs showing piping layout, valve configuration, and pump placement for reference in developing recommended modifications to enhance system effectiveness.

Responded to no cooling complaint on geothermal heat pump system located in basement. Upon arrival, unit was operational but customer reported insufficient cooling capacity. Performed diagnostic evaluation of geothermal system including inspection of internal components, electrical connections, control boards, and refrigerant line set. Checked system pressures and temperatures using digital meters to assess heat exchange performance. Verified proper operation of all safety controls, relays, and wiring connections within air handler cabinet. Inspected water-side connections including flow center valves and expansion tank for proper configuration. System found to be functioning within operational parameters at time of service call.

Responded to no cooling complaint on residential air conditioning system. Upon arrival, verified system was running but producing no cool air. Connected refrigerant manifold gauges to outdoor condensing unit and performed system diagnostics, measuring refrigerant pressures and superheat levels to determine root cause of cooling failure.

Responded to emergency call for bathroom faucet that would not shut off. Upon arrival, found that the shut-off valve at the base of the sink had broken during customer's attempt to stop water flow, resulting in active water leak. Successfully shut off water supply to the affected fixture to stop the leak. Assessed the damaged shut-off valve and surrounding plumbing connections under the sink. Documented existing conditions including P-trap assembly, supply line connections, and cabinet interior for repair planning. Secured the area and ensured no further water damage would occur.

Responded to no heat call on Bryant Plus 90 gas furnace located in crawlspace. Upon arrival, found thermostat blank with no power. Traced issue to tripped circuit breaker or blown fuse at electrical panel. Reset breaker, restored power to thermostat and furnace. Verified thermostat display operational and system responding to temperature calls. Cycled furnace through complete heating cycle, confirmed ignition sequence, burner operation, and proper airflow. All safety controls functioning within normal parameters. System restored to full operation.

Performed AC start-up procedures on recently installed system using Fieldpiece SMAN digital manifold gauge to verify proper refrigerant pressures, superheat, and subcooling readings. All system parameters measured within acceptable ranges, confirming successful installation and operational readiness.

Responded to no hot water complaint following recent AC installation in tight workspace. Upon arrival, inspected gas water heater and verified gas control valve had been inadvertently switched to off position, likely bumped during AC installation work. Restored gas supply to water heater, relit pilot light, and verified proper operation and hot water delivery to fixtures throughout home.

Installed PHCC battery backup combination sump pump system in basement sump basin. The installation included mounting the primary blue pump unit in the circular concrete basin, connecting multiple discharge pipes including white PVC piping, and routing electrical cables for power supply. Configured the battery backup system to provide emergency pumping capability during power outages, ensuring continuous flood protection for the property.

# HVAC Complete System Installation Successfully completed full HVAC system replacement including installation of Carrier Comfort Series single-stage air conditioner (model 26SCA424N003), evaporator coil (model CVAVA3014XMA), and single-stage gas furnace (model 58SB0B070M14--12). Removed and recycled existing equipment from residential property. ## Equipment Installation Installed outdoor condensing unit on new 2" PVC pad against exterior wall with proper clearances maintained. Mounted new electrical disconnect and whip for condenser power supply. Positioned evaporator coil and furnace indoors, completing changeout from existing 80% efficiency system. All equipment installed per manufacturer specifications and local code requirements. ## System Connections and Testing Reconnected to existing refrigerant line set after performing thorough flush and pressure test to verify system integrity. Reconnected existing supply and return ductwork to new furnace plenum. Performed refrigerant

Responded to callback for pilot light outage on Teledyne Laars boiler, second occurrence within days raising concern for potential gas leak. Upon arrival, inspected boiler system, gas supply lines, and pilot assembly. Conducted combustion analysis and gas leak detection testing throughout system. Photographed equipment nameplate and mechanical room setup for documentation. Verified proper gas pressure, checked thermocouple operation, and tested safety controls. Relit pilot light after ensuring safe operating conditions and confirmed stable flame operation before departure.

Performed seasonal maintenance on tankless water heater system, completing thorough flushing and cleaning procedure to remove mineral buildup and ensure optimal performance. Inspected all plumbing connections, verified proper operation of unit, and confirmed system functionality. Service completed within scheduled timeframe to accommodate customer's additional HVAC appointment later in the day.

Responded to service call for split copper pipe supplying exterior hose bib. Upon inspection, accessed crawl space and located compromised copper water line running through insulation between floor joists. Pipe exhibited visible split consistent with freeze damage from winter conditions. Repaired damaged section of copper supply line and verified system integrity. Tested water flow to exterior spigot and confirmed no active leaks present.

Performed comprehensive air conditioning tune-up on Carrier outdoor condensing unit. Completed standard maintenance protocol including system inspection, cleaning of condenser coils, verification of refrigerant levels, and testing of electrical components to ensure optimal cooling performance for the upcoming season.

Responded to no cooling call and performed system evaluation. Upon inspection, determined existing Coleman furnace and air handler system required replacement due to failed cooling components. Provided comprehensive estimate for complete HVAC system replacement including new air handler unit, necessary refrigerant lines, electrical connections, and ductwork modifications. Documented existing equipment configuration with furnace installation in utility closet, copper refrigerant lines, and current duct connections to support replacement specifications.

Provided estimate for replacement of 2006 Carrier gas furnace following basement flooding caused by sump pump failure. Water intrusion resulted in blower circulating water throughout the system, and inducer motor exhibited excessive noise independent of water damage. Unit currently operational but replacement recommended due to age and water exposure compromising long-term reliability.

Completed full HVAC system installation including Carrier 26SPA636W003 Performance Series single-stage air conditioner and Carrier CVAVA4217XMA evaporator coil. Removed and recycled existing equipment, installed new 2" PVC condenser pad, reconnected to existing line set with complete flush and pressure test to verify system integrity. Installed new disconnect and whip for proper electrical connection, mounted air handler unit in utility closet with PVC condensate drainage lines and proper clearances. Performed comprehensive system startup, verified refrigerant charge, airflow, and all operational parameters within manufacturer specifications. Completed post-installation quality assurance inspection, explained system operation to homeowner, and registered equipment warranty with manufacturer.