HVAC & Plumbing Services in Decatur, IN

Responded to no-cooling complaint and performed diagnostic evaluation of residential HVAC system. Found outdoor unit condenser coil severely deteriorated and non-functional. Confirmed thermostat calling for cooling mode but system not producing conditioned air, though outdoor fan motor operational. Documented existing Carrier furnace and current ecobee smart thermostat installation. Provided estimate for complete air conditioning system replacement due to failed evaporator coil and associated equipment condition.

Returned to complete refrigerant charge adjustment on backup heat pump system that requires R32 refrigerant. System was previously serviced but charge could not be properly dialed in due to cold ambient temperatures below 65°F. With warmer weather conditions now present, performed vacuum test showing system holding at 90 microns, confirming system integrity. Proceeded to add R32 refrigerant and dialed in charge to manufacturer specifications for optimal system performance.

Inspected damaged hose bib and existing dryer vent termination that was exiting through a 4-inch cast-iron pipe. Provided estimate for replacement hose bib installation and upgrade to a new 4-inch aluminum dryer vent pipe with exterior termination kit. Customer approved the quoted work and supplied their own dryer termination kit for easier maintenance. Scheduled follow-up installation appointment to complete both the hose bib replacement and dryer vent termination upgrade.

Conducted on-site evaluation of non-functional air conditioning system in residential basement that has been inoperative for approximately two years. Assessed existing HVAC equipment including air handler unit with connected plenum and ductwork distribution system. Documented current system configuration and conditions to provide replacement estimate for new AC unit installation in preparation for property sale.

Completed scheduled cooling season maintenance on geothermal heat pump system located in basement utility area. Performed standard preventive maintenance procedures including system inspection, filter check, and operational testing to ensure proper cooling performance for the upcoming season.

Completed on-site evaluation for adding air conditioning system to existing heating-only setup. Assessed current YORK furnace installation in basement and existing ductwork configuration to determine compatibility and requirements for AC integration. Documented existing equipment specifications and thermostat setup to provide comprehensive estimate for central air conditioning addition.

Completed full furnace changeout by removing and recycling existing equipment and installing new Carrier 59TP7A040V17--12 Performance 97 Series two-stage gas furnace with 97% AFUE efficiency rating. Installed Honeywell Vision PRO TH8321R1001 programmable thermostat and reconnected existing supply and return ductwork to new unit. Performed complete electrical wiring connections, verified proper voltage and amperage readings using digital multimeter, and ensured all safety controls functioning correctly. Installed PVC venting system for high-efficiency condensing furnace operation and verified proper drainage. Conducted system startup, adjusted gas pressure, verified temperature rise across heat exchanger, and confirmed two-stage operation cycling properly. Performed post-installation quality assurance walk-through with senior technician to verify installation standards met. Explained thermostat programming and system operation to homeowner, registered equipment warranty with manufacture

Performed maintenance flush on Navien NPE-240S tankless water heater unit. Accessed internal components, connected diagnostic equipment to monitor system parameters, and completed descaling flush procedure to remove mineral buildup from heat exchanger. Unit tested and operating within normal parameters upon completion.

Completed comprehensive AC tune-up and cooling system inspection as part of preventive maintenance program enrollment. Performed electrical diagnostics using clamp meter to verify proper amperage draw and system performance, inspected capacitor and contactor assembly with all wire connections, and confirmed all components operating within manufacturer specifications. System tested and found functioning properly with no issues identified during this first scheduled maintenance visit.

Performed comprehensive commercial HVAC tune-up including thorough blower assembly cleaning to remove accumulated dust and debris, applied evaporator coil cleaner to restore heat transfer efficiency, and replaced worn contactor to ensure reliable compressor operation. System components showed significant corrosion and weathering consistent with outdoor installation, requiring disassembly of blower housing and spiral scroll for proper access and cleaning. Unit restored to optimal operating condition with all components reassembled and tested for proper function.

Completed full HVAC system installation including Carrier Performance Series two-stage air conditioner (model 26TPA836W003), Carrier Performance 97 Series two-stage gas furnace (model 59TP7A080V17--16) rated at 80,000 BTU input with 97% AFUE, and Carrier evaporator coil (model CVAVA3617XMA). Removed and recycled existing equipment, installed new condenser unit on exterior pad against brick foundation with refrigerant lines penetrating through existing service entry point. Reconnected all existing supply and return ductwork to new air handler, completed furnace changeout utilizing installation kit for 80% to 90% efficiency upgrade. Installed GPS iWave air purification system as approved upgrade. Performed all necessary electrical connections, gas line connections, and condensate drain installation. Verified proper airflow with digital manometer reading 3.46 inches water column static pressure. Completed startup procedures, charged refrigerant system to manufacturer specifications, and v

Responded to service call for multiple plumbing issues in residential property. Addressed malfunctioning basement shut-off valve that required tapping to operate properly for both closing and reopening water supply. Replaced faulty ball valve with new unit, ensuring smooth operation without mechanical intervention. Repaired utility room faucet with difficult shutoff operation by replacing worn cartridge and internal components, restoring proper function and ease of use. Tested all repaired fixtures under normal operating pressure to verify complete resolution of reported issues.

Responded to service call for tanked water heater with suspected failing heating element. Upon arrival, inspected InSinkErator brand electric water heater unit located in garage utility area. Evaluated heating element performance, tested electrical connections at digital control panel, and assessed overall system operation including copper supply and discharge piping connections. Discussed OmniFilter water filtration system maintenance needs with customer as requested. Documented equipment condition and configuration with photographs for service records.

Installed a sewage ejector pump system in the basement to accommodate the relocation of washer and dryer from the main floor. The pump was positioned adjacent to the existing utility sink to handle gray water discharge from the relocated laundry appliances. New PVC drain lines were routed and connected to facilitate proper drainage through the pump system, ensuring compliance with code requirements for below-grade plumbing fixtures.

Performed evaporator coil replacement on Bay 1 unit. Conducted temperature diagnostics using digital thermometer, recording inlet and outlet temperatures to verify proper refrigerant flow and system performance. Completed installation and tested system operation to ensure optimal cooling efficiency.

Completed HVAC system replacement estimate and site evaluation following tech lead coordination. Documented existing outdoor condensing unit positioned against brick exterior with refrigerant line set running vertically along building wall. Interior inspection revealed furnace or air handler installation in utility room adjacent to laundry appliances, with proper warning labels present regarding refrigerant connection procedures. Photographed current equipment configuration, line set routing, and installation conditions to support replacement proposal. System assessment included evaluation of outdoor unit placement in landscaped area and interior mechanical space constraints for new equipment installation planning.

Completed replacement of two water filtration cartridges on existing whole-house water treatment system installed in basement utility area. Removed old filter elements from clear housings mounted on copper supply lines beneath floor joists. Installed new carbon block filter cartridges, ensuring proper seating and O-ring placement. Verified all brass fittings and connections were secure at filter head assemblies with blue caps. Pressurized system and checked for leaks at housing seals and pipe connections. Confirmed proper water flow through filters and verified system operation with no signs of bypass or leakage.

Conducted on-site evaluation for complete HVAC system replacement including geothermal heat pump unit and aging gas furnace. Assessed existing geothermal system that had been previously serviced earlier in the year but is now inoperative. Performed equipment inspection and took measurements of mechanical room space to determine clearances and equipment sizing requirements for replacement installation. Documented current system configuration including ductwork, refrigerant lines, and existing equipment placement. Provided comprehensive replacement estimate for both geothermal unit and gas furnace system due to age and condition of existing equipment.

Installed dedicated electrical circuits in basement utility area to support washer and dryer installation. Ran new wiring and established proper electrical connections in preparation for appliance hookup once equipment is relocated to final position.

Completed comprehensive air conditioning tune-up on residential HVAC system located in basement utility area. Performed standard maintenance procedures including inspection of air handler unit, ductwork, and associated components, verified proper operation of all system controls, and ensured equipment is ready for cooling season.