HVAC & Plumbing Services in Fort Wayne, IN

Responded to service call for zone board issue. Upon inspection, accessed mechanical equipment and zone control system. Photographed existing zone board configuration and completed necessary repairs to restore proper multi-zone operation.

Replaced faulty terminal block with multiple wire connections showing signs of wear and aging. Secured all electrical connections including blue, yellow, red, orange, and black wires to new terminal assembly, ensuring proper wire routing and strain relief within the equipment enclosure. System tested and operational upon completion.

Responded to no cooling call on 10+ year old rooftop unit. Upon inspection, found failed 50 amp 600V fuses in the main disconnect. Replaced all three TRS350R fuses, verified proper electrical connections, and tested contactors for proper operation. Unit restored to normal cooling operation with all electrical components functioning within specifications.

Responded to no cooling complaint on residential air conditioning system with history of refrigerant leak from 2017. Upon arrival, performed diagnostic evaluation of outdoor condensing unit and indoor evaporator coil system. Utilized electronic leak detection equipment to inspect refrigerant circuit and identify source of system failure. Documented equipment condition with photos showing outdoor condenser unit and leak detection process at indoor coil assembly.

Responded to no cooling complaint on commercial Bard HVAC unit serving construction trailer. Upon inspection, diagnosed failed ICM Controls relay module (model RLVS-AG1719-1) preventing compressor operation. Documented control board condition and wiring configuration with photos for approval prior to proceeding with repairs.

Successfully installed owner-provided toilet in master bathroom with new chrome flush handle and brass arm assembly. Replaced washer box valves with quarter-turn type handles for improved operation and ease of use. Rebuilt existing toilet fill valve and installed Mansfield 210/211 gasket to ensure proper function and prevent leaks.

Completed full HVAC system installation including outdoor condensing unit model 26SCA442N003 positioned on gravel pad with proper drainage and clearances against exterior wall. Installed indoor air handler unit model CVAVA4821XMA with refrigerant line set connections, ensuring proper insulation and routing of copper lines. Upgraded thermostat to Honeywell Home ElitePRO S1200 Smart Thermostat with IAQ control compatibility, programmed for optimal system operation and connected to HVAC equipment. Verified all electrical connections, tested system startup and operation, confirmed proper airflow and refrigerant charge levels, and ensured all safety controls functioning correctly.

Completed commercial rooftop unit tune-up and cleaning in preparation for heating season. Inspected filter bank containing multiple pleated air filters in metal housing, performed heating system operational check, and addressed maintenance that had been deferred from previous year.

Completed full HVAC system installation in basement mechanical room, including Carrier furnace unit with integrated ductwork distribution system, air handler with humidifier component, and outdoor condensing unit. Installed white PVC venting system routed through ceiling joists, established metallic supply and return ductwork connections, and integrated copper refrigerant line set between indoor and outdoor equipment. Configured Honeywell Home programmable thermostat (model TH6210U2001) with battery backup and mounted control wiring throughout system for proper communication between all components, ensuring complete heating and cooling functionality with proper airflow distribution and system controls operational.

Performed standard cooling season tune-up on residential air conditioning system. Conducted comprehensive system inspection including temperature differential measurements, verifying supply air temperature at floor register reading 50.6°F and return air temperature at 82.9°F, indicating proper system operation with approximately 32°F temperature split. All components operating within normal parameters.

Conducted on-site evaluation of 28-year-old HVAC system and existing tanked water heater for complete replacement estimate. Assessed exterior condensing unit with cylindrical housing, refrigerant line routing, and interior mechanical space including floor drain and existing plumbing infrastructure. Provided comprehensive estimate for full system replacement including transition from tanked to tankless water heater configuration.

Performed annual heating tune-up and cleaning on commercial rooftop unit that was missed during previous year's maintenance cycle. Completed thorough system inspection, cleaned RTU components, and verified heating operation to ensure proper function for the upcoming season.

Performed comprehensive air conditioning maintenance on cooling system. Conducted electrical diagnostics using digital multimeter, recording voltage readings of 483.1V at the condenser unit. Inspected condenser fan motor and associated components, verifying proper electrical parameters and operational integrity to ensure system reliability through the maintenance agreement period expiring in 2/2026.

Responded to reported water leak initially attributed to dishwasher but identified actual source as corroded copper waterlines serving the washing machine. Performed comprehensive plumbing repair including removal of outdated washer box and deteriorated copper supply lines. Cut drywall access panel to expose and extract existing washer box and corroded piping running between floors. Installed new washer box with PEX adapters and ran new supply lines through floor penetration into basement. Reconnected new PEX lines to existing copper plumbing in basement. Performed thorough drain snake service on washing machine drain line to ensure complete clearance and prevent future backup issues. Replaced leaking utility sink faucet in laundry area to eliminate active water damage concern. Upgraded water heater shut-off valves by removing outdated gate valves and installing new ball valves for improved reliability and ease of operation. All work completed to code with proper connections and leak

Conducted on-site evaluation for gas furnace and air conditioning system replacement. Assessed existing Energyfit furnace installation and measured current equipment dimensions to determine proper sizing requirements for new HVAC system. Documented existing plumbing connections, PVC condensate drainage configuration, and utility room layout to prepare comprehensive replacement estimate for complete heating and cooling system upgrade.

Performed comprehensive air conditioning tune-up including system diagnostics and electrical testing. Measured capacitor performance using digital multimeter, recording readings of 5.041 and 40.11 microfarads to verify proper compressor and fan motor operation. Inspected condenser unit components, confirmed voltage levels within manufacturer specifications, and ensured all electrical connections were secure for optimal system performance.

Responded to service call for Kohler generator with no-start condition that attempted to turn over but failed to run. Performed initial diagnostic assessment of unit, inspecting control panel functionality, battery voltage reading of 13.3V, and system parameters showing 240V output capability at 60.2Hz frequency. Documented generator condition and control panel status for diagnostic evaluation to determine root cause of starting failure.

Completed comprehensive air conditioning tune-up and preventive maintenance service on residential HVAC system. Performed standard inspection protocols including filter evaluation, refrigerant level check, electrical component testing, and condenser unit assessment. Renewed maintenance membership during initial service visit to ensure continued system reliability and performance.

Responded to water line failure beneath sink fixture. Assessed plumbing installation including chrome supply valves, copper and flexible supply lines, and white PVC P-trap drain assembly. Documented existing configuration with photos showing newly serviced system with clean connections, proper trap installation, and wall-mounted drain outlet integration.

Completed scheduled cooling maintenance on Carrier split system. Inspected outdoor condenser unit and indoor furnace, verified proper operation of all components, checked refrigerant lines and condensate drainage, and documented system condition with photographs. All equipment operating within normal parameters.