HVAC & Plumbing Services in Fort Wayne, IN

Evaluated existing HVAC system consisting of a 4-5 year old Bryant heat pump and an 18-year-old air handler with compatibility issues. Assessed air handler performance concerns and provided replacement estimate options, including scenarios for air handler replacement only and complete system replacement due to refrigerant type considerations to ensure proper equipment compatibility and system efficiency.

Responded to afterhours emergency call for no water condition at residence. Coordinated with municipal water department for service shutoff to facilitate repair. Upon inspection, identified failed ball valve on main water supply line. Removed deteriorated brass valve assembly and corroded copper fittings from service line. Replaced defective ball valve with new brass valve assembly, ensuring proper connection to existing copper supply pipe. Restored water service and verified system operation with no leaks detected.

Responded to water leak complaint affecting two fixtures on main floor. Inspected kitchen and bathroom sink drain assemblies and supply connections. Accessed basement/crawl space to examine overhead plumbing infrastructure including copper supply lines, PVC drain lines, and associated pipe supports mounted to floor joists. Identified source of leakage, performed necessary repairs to eliminate water intrusion beneath both sink locations. Verified all connections secure and tested system for proper drainage and absence of further leaks. Work completed successfully with customer payment received.

Completed installation of customer-provided reverse osmosis water filtration system under kitchen sink, including all necessary connections and supply lines. Replaced shut-off valve to washing machine with customer-provided valve. Installed new trap assembly to kitchen sink using customer-provided parts, ensuring proper drainage and seal connections.

Performed AC system start-up on recently installed unit. Connected refrigerant manifold gauges to verify system pressures and temperatures, confirmed proper refrigerant charge levels, and documented operational parameters to ensure system is functioning within manufacturer specifications.

Performed air conditioning system startup following previous installation. Utilized Fieldpiece SMAN digital manifold gauge to verify refrigerant pressures and temperatures, confirming proper system operation with readings of 110.9 PSIG suction pressure at 107.4°F and 243.6 PSIG discharge pressure. System startup completed successfully with all parameters within manufacturer specifications.

Completed coil installation in Bay 1 as scheduled. Measured and documented existing copper refrigerant line dimensions showing significant corrosion and oxidation on vertical suction line. Installed new evaporator coil assembly with proper connections to existing copper refrigerant lines and secured all mounting brackets. Charged the A/C system to manufacturer specifications upon completion and verified proper operation.

Conducted on-site assessment for geothermal unit installation at waterfront residential property with planned addition. Evaluated existing HVAC system consisting of two propane furnaces in basement and one heat pump, with proposed geothermal unit placement in garage. Provided comprehensive estimate for geothermal system replacement to serve expanded living space, with foundation preparation in early stages at time of visit.

Installed two duct detectors in rooftop unit (RTU) electrical control panels to meet fire marshal compliance requirements. Connected detectors to existing alarm circuits with proper wiring terminations and verified operational functionality of both smoke detection devices upon completion.

Installed Grundfos recirculation pump with comfort valve at water heater to address extended hot water delivery time to master bathroom lavatories. Mounted pump assembly on top of water heater tank with appropriate copper and flexible connector piping, installed digital control unit, and positioned comfort valve under master bathroom sink cabinet. System tested and operational, significantly reducing wait time for hot water delivery to fixtures.

Responded to water damage complaint affecting ceiling below second-floor bathroom. Upon inspection, discovered active moisture intrusion and dripping originating from bathroom area above damaged ceiling. Homeowner had already opened ceiling to expose extent of damage, revealing significant mold growth within wall cavity behind bathtub surround. Inspected bathroom fixtures including shower valve, showerhead assembly, tub spout, and overflow drain for potential leak sources. Documented conditions with photographs showing bathtub installation and exposed wall cavity with visible mold contamination. Confirmed moisture presence and active water intrusion requiring immediate attention. Advised homeowner that mold remediation specialist would need to address biological growth before plumbing repairs could proceed. Identified bathroom plumbing system as source of water damage requiring further investigation once remediation complete.

Completed estimate for adding central air conditioning system to existing gas furnace installation in basement. Evaluated current furnace unit and existing thermostat wiring configuration to determine compatibility for AC integration. Provided Carrier brand equipment options and specifications for split system installation that would work with the current heating setup.

Responded to no heat call on commercial HVAC unit less than 10 years old. Upon inspection, found control board with disorganized wiring and visible corrosion on interior metal surfaces. Inspected electrical connections, terminal blocks, and relay components on control board assembly. Documented existing conditions of blower motor housing, circuit board wiring, and overall system components for service records.

Conducted site evaluation for garage heating system installation. Assessed existing electrical infrastructure including breaker panel and utility boxes, evaluated ceiling structure and available mounting locations for heating equipment, and documented current mechanical systems and ductwork configuration. Provided multiple heating options based on space requirements and existing utility connections.

Completed installation of customer-supplied air handler and outdoor A/C unit in end closet location. Installed Goodman GN4SAN418-A air handler with matching condensate pump system and connected outdoor condensing unit, verified all electrical connections per manufacturer specifications at 208-230V, installed black flexible ductwork from air handler to ceiling plenum, and confirmed proper refrigerant line connections. Removed and transported old equipment to maintenance facility per property requirements.

Responded to service call for removal of fence-mounted lighting fixtures. Upon arrival, assessed the installation which consisted of exterior lights mounted along a residential fence line with associated electrical wiring running through landscaped areas at the base of the brick structure. Disconnected electrical supply to the lighting circuit and verified power was de-energized before proceeding with removal work. Removed all fence-mounted light fixtures and associated mounting hardware from the brick wall. Extracted the bright blue-green electrical cable that was routed through the ivy bed and garden area along the foundation. Properly capped and secured all electrical connections per code requirements. Removed all mounting brackets and hardware, leaving the brick wall surface ready for any future installations or repairs as needed by the customer.

Completed comprehensive plumbing system installation including a Bradford White 50-gallon electric water heater with 2.1-gallon expansion tank, 33.5-gallon well tank with new tank tee, pressure switch, and gauge, and Sterling 1.5 cubic foot water softener with brine tank and two bags of salt. Reconnected well tank to existing well line in garage floor and reconnected to existing hot and cold water distribution lines in garage. Chipped up concrete flooring as necessary to access and repair kinked copper supply lines beneath slab. Installed new kitchen sink and faucet. Performed pressure testing on all existing water lines to verify system integrity and confirm no leaks present under slab foundation. All work completed with proper permits obtained.

Installed new LED lighted mirror in bathroom and removed existing vanity light fixture. Installed medicine cabinet and completed associated electrical connections to ensure proper operation of all new fixtures.

Conducted on-site evaluation of existing 20-year-old HVAC system for complete replacement estimate. Assessed outdoor air conditioning condenser unit and indoor gas furnace components, documented current equipment model numbers and specifications, and photographed existing installation including refrigerant line routing and electrical connections. Provided comprehensive replacement quote for new matched AC and furnace system.

Temporarily removed newly installed air handler unit to allow access for medicine cabinet extraction from wall cavity. Unit will be reinstalled following drywall repair and patching work by another technician.