HVAC & Plumbing Services in Angola, IN

Provided estimate for replacement of existing AO Smith gas water heater located on main floor of residence. Unit currently operational but producing discolored water. Assessed installation area, gas line connections, and venting requirements. Discussed options for standard tank replacement versus tankless water heater conversion based on homeowner's request to explore tankless alternatives.

Provided comprehensive estimate for complete HVAC system replacement including furnace, air conditioning unit, and ductwork replacement following damage requiring remediation. Inspected existing York air handler unit and associated PVC condensate drainage system in utility closet, finding no visible water damage or leakage in accessible areas beneath the structure. Recommended smoke testing of drainage system to identify potential air leaks, with customer approving procurement of materials and scheduling return visit with two technicians to perform diagnostic smoke test using tall ladder and 3" fernco coupling for proper system evaluation.

Responded to no-cooling complaint on rooftop unit serving server room. Upon arrival, inspected RTU condenser unit and investigated reported noise issue. Unit found operating on concrete pad with standard configuration and no visible external damage to housing or components.

Conducted comprehensive on-site evaluation for complete HVAC system replacement including air conditioning unit and gas furnace. Assessed existing electrical infrastructure and panel capacity to determine compatibility requirements for new equipment installation. Provided detailed estimate for full system replacement of main HVAC unit and prepared separate quotation for additional split system installation to serve upper level of residence.

Conducted on-site assessment of existing HVAC system for replacement estimate. Evaluated current equipment including furnace/air handler, outdoor condensing unit (KING brand), and associated ductwork in basement mechanical room. Documented system configuration, equipment specifications, and installation requirements. Photographed existing components including water heater proximity, electrical connections, ductwork layout, and outdoor unit placement on concrete pad. Provided comprehensive replacement recommendations based on current system condition and home requirements.

Conducted equipment evaluation for non-cooling air conditioning system. Documented existing Carrier thermostat and outdoor condenser unit condition. Scheduled replacement estimate consultation to provide system options and recommendations for complete AC replacement.

Completed annual cooling system maintenance as part of first preventative maintenance visit under active service agreement. Performed comprehensive inspection of air conditioning unit including refrigerant level check, electrical connections, condensate drain system, and overall system operation. Documented hydronic heating system components present at property with photographic records for future reference, noting expansion tank, manifold assembly, and associated piping in good condition.

Completed preventive maintenance on Rheem tanked water heater located in garage utility room. Performed standard water heater flush procedure to remove sediment buildup from tank bottom, inspected all copper supply and discharge piping connections, verified proper operation of temperature and pressure relief valve, and examined expansion tank mounting and pressurization. Checked burner assembly access panel, confirmed pilot light operation through viewing window, and inspected venting system integrity. All plumbing connections, shut-off valves, and support legs found secure with no visible leaks or corrosion. Unit operating within normal parameters upon completion.

Completed full HVAC system replacement including installation of Carrier 26SCA430N003 single-stage air conditioner, Carrier CVAVA3617XMA evaporator coil, and Carrier 58SB0B070M17-12 single-stage gas furnace with Honeywell T6 thermostat. Removed and recycled existing equipment, then reconnected to existing line set after flushing and pressure testing for optimal performance. Installed new 2" PVC condenser pad with pea gravel base for proper outdoor unit support and drainage. Performed LP conversion on furnace unit to accommodate propane fuel source. Installed Honeywell 4" media air cleaner for improved indoor air quality. Reconnected all existing supply and return ductwork to new equipment. Installed new electrical disconnect and whip for outdoor condenser unit with proper electrical connections. Completed comprehensive system startup and testing procedures to verify proper operation of all components. Provided thorough explanation of thermostat operation and system controls. Conduc

Responded to no cooling complaint on residential air conditioning system. Upon arrival, located outdoor condensing unit surrounded by landscaping and performed diagnostic evaluation of both outdoor and indoor equipment. Inspected furnace/air handler with access panel removed, examined internal components including control board, wiring connections, and mechanical assemblies. Assessed system operation and identified cause of cooling failure, completing necessary repairs to restore proper function.

Completed installation of geothermal heat pump system with associated mechanical equipment. Installed Rheem MODEL W6B003BBN1A0210F3D10 geothermal unit with electrical service rated at 208-230V, 60Hz, requiring 36.7/44 circuit amperage and 43/46.5 minimum circuit amps. Unit manufactured in Fort Wayne, Indiana, serial number 260601319, job number 831879. Mounted and secured main heat pump unit to wall with proper specification labeling affixed for future reference and compliance documentation. Installed complete domestic hot water system integration including Rheem electric water heater with expansion tank assembly. Mounted blue pressure/expansion tank to wall with proper support and connected via copper piping with brass fittings and compression connections. Ran copper supply and return lines from geothermal unit to water heater with appropriate shut-off valves at key connection points. Installed black flexible connector hose between plumbing manifold and water heater inlet. Connected

Responded to report of water leaking from base of electric tanked water heater in basement, specifically the right-hand unit of a dual water heater installation. Upon inspection, identified active leak originating from lower tank section, with homeowner noting leakage occurred primarily during shower usage. Diagnosed failed tank integrity due to internal corrosion, as leak source was determined to be from tank body rather than fittings or connections. Recommended and completed full water heater replacement due to compromised tank structure that cannot be repaired. Installed new electric tanked water heater with proper copper piping connections, flexible supply lines, and code-compliant safety features. Verified all connections for proper seal integrity, tested unit operation, and confirmed no additional leaks present on either water heater system.

Completed first prepaid cooling system maintenance visit after rescheduling due to previous service delays. Performed standard system diagnostics and temperature measurements on HVAC equipment and ductwork, documenting supply air temperatures and system performance readings with digital instrumentation.

Completed routine air conditioning maintenance on cooling system. Performed standard inspection, cleaning, and testing procedures to ensure optimal performance and efficiency. System operating properly with temperature readings within normal parameters at time of service.

Completed routine air conditioning maintenance visit on cooling system. Performed standard seasonal inspection and preventive maintenance procedures. Measured supply air temperature at floor register, which indicated proper system operation at 81.5°F.

Completed full installation of a 24kW standby generator system including a 200-amp automatic transfer switch, concrete pad foundation, battery with warmer, oil warmer, and natural gas supply line. The generator unit was mounted on the prepared concrete pad with proper clearances from the structure, all electrical connections were made to code, and the ATS was integrated with the main electrical panel to enable seamless automatic power transfer during outages.

Conducted on-site evaluation of existing Culligan water treatment system in garage utility area for customer dissatisfied with current water quality. Assessed installation space constraints adjacent to large capacity water heater and existing water softener equipment. Discussed reverse osmosis system options as potential solution for improved water quality in lake home application. Evaluated feasibility of tankless water heater conversion to create additional space for upgraded water treatment equipment. Documented current plumbing configuration including water softener tanks, filtration housing, and copper supply line routing. Provided recommendations for enhanced water treatment solutions to address non-sulfur water quality concerns.

Installed a 50-gallon natural gas water heater in garage, mounting unit on an elevated stand as requested by property owner. Connected copper supply lines, installed blue expansion tank, and integrated gas control valve with temperature settings. Verified proper venting, tested pilot ignition system, and confirmed all connections were secure and operational per manufacturer specifications.

Replaced leaking 50-gallon residential water heater in utility room under warranty coverage. Removed failed unit and installed new A.O. Smith water heater with Honeywell gas control valve, verified all plumbing connections, tested gas lines for leaks, and confirmed proper operation of pilot light and burner assembly. Unit is functioning correctly with appropriate temperature settings and all safety controls operational.

Completed comprehensive estimate for full HVAC system replacement including furnace and air conditioning unit, both originally installed in 2003 and reaching end of service life. Assessed existing basement-installed furnace with overhead ductwork and evaluated airflow deficiency to master bedroom. Documented current equipment specifications including model KGGRC 120C-20C unit and photographed existing duct configuration to provide replacement options addressing inadequate air distribution to primary living areas.