HVAC & Plumbing Services in Angola, IN

Responded to service call for leaking pipe in crawlspace and clogged toilet. Inspected and repaired copper piping with visible wear and connection issues in crawlspace area, applying appropriate wrapping and securing fittings to stop leak. Successfully cleared toilet blockage and verified proper drainage and flush operation before completing service.

Responded to no cooling call with reported water leakage around furnace and water accumulation in crawlspace ductwork. Upon arrival, inspected utility room furnace area and crawlspace to assess water intrusion source and extent of moisture in duct system. Documented crawlspace conditions including plumbing configuration and structural areas where water had collected, noting PVC drain lines and ductwork routing beneath floor joists.

Responded to report of water damage visible in basement ceiling below main floor bathroom. Removed ceiling tile to access plumbing infrastructure and inspected PVC sewer line connections. Identified loose PVC joint connection requiring proper solvent welding to prevent future leakage. Applied PVC primer and cement to secure connection, ensuring watertight seal per plumbing code standards.

Responded to no heat call on Goodman furnace system. Customer suspected failed ignitor as cause of heating failure. Upon arrival, inspected furnace unit located in basement, verified no heat condition, and diagnosed ignition system malfunction preventing burner operation.

Conducted follow-up site assessment for full HVAC system replacement after previously quoting air conditioning unit only. Documented existing thermostat configuration and electrical service panel with proper circuit breaker arrangement to ensure compatibility with proposed heating and cooling equipment installation.

Conducted comprehensive assessment of aging gas furnace system in residential basement for replacement estimate. Evaluated existing HVAC infrastructure including deteriorated galvanized ductwork, exposed foundation conditions with moisture damage and efflorescence on masonry walls, and current furnace cabinet configuration. Documented system layout, duct connections, and structural considerations for furnace replacement recommendation.

Completed installation of 22kW Generac propane-fueled standby generator with 200-amp automatic transfer switch (ATS) positioned approximately 20 feet from residence on pre-existing concrete pad adjacent to propane tank. Installation included oil warmer and battery warmer for cold-weather operation reliability. Ran conduit from generator to exterior-mounted ATS enclosure on home's siding, ensuring proper electrical connections between generator, transfer switch, and existing electrical service panel. Verified all electrical connections, tested ATS functionality, and confirmed generator startup and automatic transfer capabilities. System commissioned and operational, providing whole-house backup power protection.

Responded to no cooling complaint on newly installed rooftop HVAC system. Upon arrival, verified outdoor condensing unit and associated electrical components were properly installed with correct refrigerant line connections and condensate drainage in place. System inspected and found to be operational with all connections secure and equipment functioning as designed.

Replaced condenser unit under CFAD 100% program coverage. Coordinated arrival time with customer per their schedule request. System tested and verified operational with proper refrigerant pressures and temperatures recorded using digital manifold gauges, confirming satisfactory performance of new condenser installation.

Responded to urgent no-cool call on recently installed AC unit and discovered missing condensate drain line, causing four months of continuous water discharge into crawlspace. Documented extensive water damage including flooded crawlspace, warped and sinking bedroom floor, and severe moisture staining on wooden subfloor and structural components. Photographed water damage patterns on plywood decking showing vertical streaking and discoloration from prolonged moisture exposure, deteriorated composite materials, and affected areas near HVAC ductwork and insulation. Identified improperly installed air conditioning system lacking required primary drain line, resulting in catastrophic water intrusion and compromised structural integrity. Assessed cooling performance concerns in addition to water damage remediation needs.

Completed comprehensive tune-up maintenance on residential AC unit. Performed thorough inspection of electrical components including terminal connections, capacitor, and control wiring. Capacitor showed signs of age with surface corrosion noted on terminals; all electrical connections were verified secure and system tested for proper operation.

Completed prepaid cooling maintenance visit on residential HVAC system. Upon inspection, discovered severely rusted capacitor with deteriorated wiring connections and corroded electrical terminal block with multiple discolored brass screws showing signs of age and oxidation. Documented equipment condition with photographs for maintenance records. System components exhibited extensive environmental exposure and corrosion requiring attention for continued safe operation.

Completed installation of 18KW Generac standby generator system including 200-amp automatic transfer switch, battery warmer, oil warmer, concrete pad, and battery. All components were properly wired and connected to the main electrical panel, with the ATS configured to automatically switch power sources during utility outages. System was tested for proper operation and first year maintenance package was included with the installation.

Successfully installed a new tanked water heater in the utility room as part of a coordinated HVAC system upgrade. The installation included proper connection of copper supply lines, pressure relief valve piping, and integration with the existing plumbing infrastructure alongside the Carrier HVAC equipment. All connections were tested and verified for proper operation, with the digital control panel programmed and the system commissioned for immediate use.

Responded to service call for leaking kitchen faucet and successfully completed replacement with customer-supplied fixture. Removed existing faucet assembly, installed new chrome high-arc faucet with dual cross-handle controls and separate spray attachment on stainless steel double-basin sink, ensuring proper connections and testing for leaks. System verified operational with no leaks detected upon completion.

Completed first prepaid cooling system maintenance visit. Performed comprehensive system inspection and diagnostic testing using digital multimeter, recording temperature readings of 495°F at critical measurement points. Inspected dual-rated capacitor (45/5 MFD, 440V AC) with all four terminal connections intact and functioning properly, confirmed proper wire connections on compressor, fan, and common terminals.

Completed final prepaid cooling maintenance visit on residential HVAC system. Performed standard system diagnostics using digital multimeter to verify electrical readings and inspected Genteq capacitor (model D147086P41, 440VAC) which showed proper operation at 4.932 reading. All components functioning within normal parameters; system operational and ready for continued service through contract expiration.

Completed comprehensive air conditioning tune-up and cooling system inspection as part of preventive maintenance program. Performed electrical diagnostics using digital multimeter to verify proper voltage, amperage, and capacitor readings across system components. All measurements confirmed within manufacturer specifications, ensuring optimal system performance and efficiency for the cooling season.

Completed preventive maintenance on residential air conditioning system at rental property. Inspected outdoor condenser unit, which showed signs of age and weathering with visible dirt accumulation on exterior surfaces and top panel. Examined electrical terminal connections and found significant buildup of dirt, dust, and debris on wiring and terminal block components. Performed standard cooling season maintenance procedures including inspection of condenser coils, verification of electrical connections across multiple circuits, and assessment of unit operation. System operational upon completion of maintenance visit.

Completed half-system replacement installation of Carrier Comfort Series 26SCA436N003 single-stage air conditioner with matching Carrier CVAVA4217XMA evaporator coil. Removed and recycled existing outdoor condensing unit and indoor coil, then installed new equipment utilizing existing supply and return ductwork in indoor utility area. Reconnected to existing refrigerant line set after performing complete flush and pressure test to ensure system integrity. Installed new outdoor condensing unit on 2-inch PVC pad with pea gravel base for proper drainage and leveling, mounted new electrical disconnect box and whip for code-compliant power supply. Completed all refrigerant connections, performed leak test, evacuated system, and charged to manufacturer specifications. Verified proper airflow, temperature split, and operational performance of single-stage cooling system. Registered manufacturer warranty coverage for both air conditioner and evaporator coil providing 10-year limited parts prot