HVAC & Plumbing Services in Huntertown

Installed customer-supplied mini-split system for wine room application. Ran and secured 8-inch supply duct and 10-inch return air duct through framed wall cavities using flexible insulated ductwork with proper strapping at intervals. Installed metal vent boots and plenums at termination points, cutting appropriate openings in OSB wall panels for duct penetrations and ensuring proper sealing of all connections for optimal airflow and system efficiency.

Completed on-site assessment for full HVAC system replacement including furnace and air conditioning unit. Evaluated existing equipment in basement mechanical room, documented current system specifications and measurements, and assessed thermostat configuration. Provided comprehensive replacement estimate with extended labor warranty option, which was accepted by homeowner.

Performed comprehensive AC tune-up on residential cooling system per routine maintenance request. Inspected air handler unit, verified thermostat operation and calibration on Sensi WiFi-enabled model, confirmed cooling setpoint functionality at 72°F with system responding appropriately. Replaced thermostat batteries as preventative maintenance, checked all electrical connections, and documented equipment condition with no issues found during inspection.

Responded to service call for sump pump system failure causing water backup into residence. Upon inspection, found dual sump pump installation in basement with inadequate pumping capacity and operational issues preventing proper water removal. Assessed discharge system including white PVC piping and electrical connections with power strip configuration. Identified compromised pump performance leading to water accumulation on basement floor, evidenced by visible staining and moisture marks on concrete surfaces. Verified discharge line routing to exterior property where water exits into drainage area near lawn perimeter. Addressed pump functionality concerns to restore proper water evacuation and prevent further basement flooding.

Responded to service call for corroded washing machine hookup faucets requiring replacement. Upon inspection, found significant corrosion and oxidation on copper supply lines and shut-off valves with deteriorated finish on hot and cold water connections. Removed section of drywall to access plumbing system behind washer box. Assessed extent of corrosion on copper piping throughout wall cavity. Replaced corroded washing machine shut-off valves with new hot and cold water supply valves. Installed new flexible supply hoses to washer box connections. Verified all connections for proper operation and absence of leaks. Documented existing plumbing conditions with photos showing before and during repair stages.

Completed installation of second sump pump in basement basin following previous visit where initial pump was replaced due to water intrusion issues. Installed pump mechanism with PVC discharge piping configuration including vertical discharge assembly and elbow joints, connected incoming drainage hoses to basin, and verified proper operation and water removal functionality.

Responded to no cooling complaint and diagnosed air conditioning system with low refrigerant levels indicating possible leak in the system. Conducted comprehensive evaluation of HVAC equipment to provide replacement estimate, documenting existing unit condition and installation requirements. Generated detailed proposal for complete system replacement due to recurring refrigerant loss and previous repair history, including assessment of exterior condensing unit location and interior air handler accessibility.

Responded to emergency service call for non-operational sump pump causing basement flooding. Upon arrival, assessed the failed pump system and standing water conditions. Removed and replaced defective sump pump unit with new blue submersible pump assembly. Installed pump in existing sump basin and connected discharge piping using white PVC pipe with proper metal hose clamps at all connection points. Verified all mechanical fittings were secure and tested pump operation to ensure proper activation and water discharge. Documented installation with photographs showing completed pump assembly, piping configuration, and secure mounting. Contacted property management upon completion to confirm system restoration and proper operation.

Installed one 80-gallon Bradford White electric water heater (model BSLE280T6-1) in basement location. Mounted 2.5-gallon expansion tank on cold water inlet line per code requirements. Rerouted cold water supply piping to new heater and reconnected hot water distribution to existing plumbing system. Installed dedicated 30-amp electrical circuit from main breaker panel to water heater using appropriate gauge wiring and flexible metal conduit. All copper pipe connections soldered and tested for leaks. Unit energized and tested for proper operation. System includes 6-year tank and parts warranty with 1-year labor coverage.

Responded to service call for HVAC system experiencing multiple issues requiring immediate attention. Conducted comprehensive assessment of existing residential heating and cooling equipment, including outdoor condensing unit and indoor air handler installation. Evaluated current system performance, documented equipment condition through detailed photography, and provided estimate for complete HVAC system replacement to address identified deficiencies and restore proper climate control functionality.

Completed comprehensive heating system maintenance inspection as part of prepaid maintenance agreement. Performed diagnostic measurements using digital testing equipment to verify system operating temperatures and pressures, checked electrical connections and wiring integrity within the unit cabinet, and confirmed all components functioning within manufacturer specifications.

Installed natural gas line from existing residential gas meter to backup generator location. Ran approximately 8-10 feet of black iron pipe with appropriate fittings, elbows, and shut-off valve to supply fuel source for standby generator unit. Connected piping to meter assembly using code-compliant materials and secured all connections. Installation positioned along exterior foundation wall near existing HVAC equipment pad to maintain clean routing and accessibility for future service needs.

Completed comprehensive estimate for HVAC system replacement in a recently purchased two-story residence with basement. Assessed main floor furnace located in basement serving both basement and main floor areas, with existing AC unit in newer condition. Evaluated second floor system in attic space, accessing unit via pull-down stairs requiring 6-foot ladder. Documented attic-mounted furnace and air handler with existing ductwork and insulation conditions. Photographed outdoor condensing unit positioned on river rock base against exterior wall with proper electrical disconnect and condensate drainage. Noted potential undersizing concerns with second floor unit based on heating and cooling load requirements. Provided replacement options for basement furnace as standalone replacement, and complete furnace and AC system replacement for second floor attic installation to address capacity concerns and ensure proper comfort control for upper level.

Conducted an HVAC system replacement estimate at a residential property. Assessed existing equipment including a Honeywell digital thermostat and ductwork system with visible condensation issues on metallic piping, indicating potential insulation deficiencies or temperature differential concerns. Documented current system conditions and provided replacement options for complete HVAC system upgrade.

Completed comprehensive air conditioning tune-up on residential HVAC system. Performed electrical diagnostics using digital multimeter to verify proper voltage and capacitance readings at the air handler unit. Inspected and tested run capacitor connections, confirming all wire terminals were secure and electrical components were functioning within manufacturer specifications.

Completed final prepaid cooling maintenance visit for duplex property with two separate HVAC systems. Performed standard preventive maintenance inspection on Carrier furnace and cooling system located in utility closet, verified electrical connections at terminal block were secure with proper wire terminations, and documented equipment condition through photographs. Both residential units serviced per maintenance agreement, with coverage extending through October 2026.

Completed warranty parts replacement on tankless water heater unit installed in attic crawl space. Replaced defective component under manufacturer warranty, with customer responsible for labor only. Verified proper operation of unit, confirmed all PVC venting and condensate drainage lines were secure and functioning correctly, and ensured electrical connections remained intact throughout the repair process.

Completed first prepaid cooling system maintenance visit during scheduled afternoon appointment window. Performed comprehensive inspection of HVAC unit interior, examining refrigerant lines, copper piping, heat exchanger coils, and electrical connections. All copper pipes, including U-bend configurations and suction/liquid lines, were visually assessed for proper condition and signs of wear or oxidation. Verified refrigerant line insulation integrity and checked for moisture accumulation on components. Inspected aluminum fin coil structure and internal compartment housing for proper operation. System components found to be functioning within normal parameters with appropriate condensation present during cooling cycle operation.

Completed final prepaid cooling maintenance visit for one of two residential systems on property. Performed standard preventive maintenance procedures on outdoor condenser unit, including inspection of electrical connections, refrigerant levels, and overall system operation. Documented equipment condition with temperature readings and exterior unit photographs showing both condensers positioned on rock bed against building exterior with proper clearances maintained.

Performed comprehensive site evaluation for complete HVAC system replacement at residential property experiencing no cooling condition. Assessed existing outdoor condensing unit positioned on grade-level concrete pad against vinyl siding, noting weathered equipment with accumulated debris at base and standard electrical service connection via gray conduit and junction box. Evaluated indoor Bryant furnace system located in basement mechanical room with existing ductwork, PVC venting, and copper refrigerant lines. Documented current equipment specifications, electrical service requirements, and installation access points. Photographed existing equipment conditions and mechanical room layout to prepare detailed replacement estimate for new cooling and heating system installation.