HVAC & Plumbing Services in Kendallville, IN

Completed final prepaid cooling maintenance visit on Lennox condensing unit. Performed standard system inspection, verified unit operational status, and documented equipment condition with photos showing clean exterior surfaces and proper installation on concrete pad with adequate clearance from landscaping.

Responded to no cooling call on 10+ year old system. Upon arrival, found unit not blowing air. Inspected electrical components and capacitor mounted in ceiling assembly, noting age-related wear and accumulated dirt on wiring connections. Evaluated heavily soiled air filter with significant dust and debris accumulation restricting airflow. Addressed airflow issue and restored system operation.

Completed estimate for replacement of 25-year-old WaterFurnace geothermal system experiencing low pressure compressor trips and cooling failures. Assessed open loop geothermal configuration on main floor, documented existing equipment condition including air handler and mechanical connections, and replaced air filter. Provided comprehensive replacement options and recommendations for new geothermal heat pump system.

Completed annual air conditioning maintenance on residential Carrier condenser unit and associated indoor HVAC system. Performed comprehensive system inspection including evaluation of outdoor condenser components, heat exchanger coils, refrigerant lines, and indoor furnace connections. Verified proper operation of all equipment, confirmed adequate airflow through ductwork system, and documented system condition with photographic records showing unit in good working order with no immediate service needs identified.

Tech lead Alex conducted a comprehensive HVAC system replacement estimate and documentation. Detailed photographic assessment was performed of the existing unit's internal components, including electrical wiring configurations, blower motors, control boards, and condensate management systems. The inspection revealed an aging system with visible wear, accumulated debris, and potential maintenance concerns requiring full system replacement evaluation.

Completed first prepaid preventive maintenance visit on commercial cooling system consisting of 7 AC units equipped with 1-inch filters. Performed comprehensive inspection and testing of all units, including electrical diagnostics using digital multimeter to verify proper voltage and amperage readings. Documented filter specifications and unit identifications for future service reference, creating filter list for ongoing maintenance program. All units inspected and found operational at time of service.

Responded to no cooling call on 10+ year old HVAC system with thermostat communication failure. Found thermostat displaying communication error after customer replaced batteries. Inspected condensate drain system and observed PVC drainage components with residue buildup, standing water in drain pan area, and damaged insulation board near unit, indicating potential drainage issues that may have contributed to system protection shutdown.

Completed routine cooling system maintenance for monthly member. Accessed outdoor condensing unit and inspected electrical components including capacitor, contactors, and wiring connections. Removed significant accumulation of dried grass, plant material, and debris from interior compartment and base of unit that had built up from outdoor exposure. Performed electrical testing with multimeter probes to verify proper voltage and component operation. Cleaned debris from concrete pad surrounding unit. All electrical connections secure, components operating within normal parameters. System running efficiently following maintenance and cleaning procedures.

Provided estimate for bathtub removal and replacement on main floor. Assessed existing fixture location, plumbing connections, and surrounding wall conditions to determine scope of work for installing new bathtub in same location.

Conducted on-site evaluation of detached residential garage for gas furnace replacement estimate. Assessed existing heating infrastructure, electrical panel capacity, gas line accessibility, and workspace configuration. Documented current conditions including overhead heating panel, electrical service availability, and clearance requirements for new equipment installation. Provided comprehensive replacement quote for appropriately-sized gas furnace suitable for garage workshop application.

Responded to no hot water complaint on A.O. Smith 40-gallon natural gas water heater (Model GCR-40 410) installed in main floor utility closet. Upon arrival, confirmed unit had shut off with no pilot light indication. Inspected gas control valve, thermocouple, and pilot assembly. Relit pilot light, verified proper flame characteristics, and tested burner operation through full heating cycle. Confirmed hot water restoration and proper unit function before departure.

Performed startup and commissioning of newly installed air conditioning system. Utilized Fieldpiece SMAN refrigerant manifold and micron gauge to verify proper refrigerant charge and system pressures, confirming R454B refrigerant levels and superheat readings within manufacturer specifications at 26°F. All system parameters tested and operating normally upon completion.

Responded to no cooling call on heat pump system. Upon arrival, performed system diagnostics and temperature measurements. Supply air temperature measured at 47.1°F, indicating unit was operating in heating mode rather than cooling mode. Troubleshot thermostat settings and system controls, reversed system operation from heating to cooling mode. Verified proper refrigerant line temperatures and confirmed system restored to normal cooling operation.

Completed routine cooling maintenance on residential Trane air conditioning system. Performed standard inspection of outdoor condenser unit, verified electrical connections at disconnect box, and tested system operation using digital multimeter to confirm proper amperage draw of 35.25 amps. All components functioning within normal parameters with no issues identified.

Completed first prepaid cooling maintenance visit on residential HVAC system. Performed comprehensive system inspection including electrical panel evaluation, capacitor testing with digital multimeter showing normal readings, and verification of contactor operation. All components functioning within manufacturer specifications with no deficiencies noted.

Completed first-visit air conditioning maintenance on Carrier HVAC system as part of membership agreement expiring in January 2027. Performed comprehensive inspection of cooling equipment, verified electrical measurements using clamp meter showing proper amperage readings, and documented system condition through photographs. All components operating within normal parameters with no immediate service needs identified.

Performed routine maintenance on tanked water heater located in garage mechanical room. Completed full tank flush to remove sediment buildup, tested temperature and pressure relief valve for proper operation, and inspected all copper supply lines and brass fittings for leaks or corrosion. Verified expansion tank pressure and confirmed all safety labels and manufacturer specifications were visible and legible. System is operating within normal parameters.

Performed AC start-up on recently installed outdoor condensing unit. Connected digital manifold gauges to service ports and verified system pressures, temperatures, and refrigerant charge levels were within manufacturer specifications. Applied protective spring jacket to unit and confirmed all safety labels and warning placards were properly affixed and legible.

Removed existing toilet and installed new white porcelain toilet in residential bathroom. Secured unit to floor flange with new wax ring seal and closet bolts, reconnected water supply line, and tested for proper operation and leaks. Verified flush mechanism functioned correctly and left work area clean with all fixtures operational.

Responded to follow-up service call for previously installed Moen kitchen faucet experiencing recurring low water pressure issues. Inspected faucet assembly, aerator, and supply line connections to identify cause of reduced flow. Performed necessary adjustments and testing to restore proper water pressure to the fixture.